Parts to suit Ammco
 
 

GT-3161 Drive V-Belt

V Belt for Ammco 3000/4000.

To top

GT-10241 Drive V-Bel

For Ammco 3000/4000. Increases arbor speed and power.

To top

GT-3024 Pulley (small) for 4000 Ammco

GT-3024 Pulley (small) for 4000 Ammco

To top

GT-5002 20-1/4in. Belt for GT-5001

For Ammco 3000/4000.

20.25 inch long

To top

GT-5001 Serpentine Belt Pulley Set Ammco

Gives your brake lathe more pulling power & increases arbor speed up to 200RPM. Virtually eliminates vibration.

Replaces V pulley system on all AMMCO lathes.

To top

GT-5003 19 in. Belt for GT-5001

For Ammco 3000/4000.

19 inch long

To top

5-1/2 in. Hold Down Stud (GT-3031)

Tooling hold-down pieces, fits all Ammco Lathes

Short stud, 5 1/2”

To top

6-1/2 in. Hold Down Stud (GT-25913)

Tooling hold-down pieces fits all Ammco lathes. Used with GT-11227 nut to replace washer set.

Long stud, 6 1/2in

To top

Rubber Spindle Boot (RSB-3085)

Fits Ammco models 3000, 4000, 4100 and 7700

To top

Rubber Spindle Boot Kit (RSB-KIT)

Fits Ammco models 3000, 4000, 4100, 7700. Kit includes rubber spindle boot, boot ring, C-clip and snap-ring (all sold individually as well).

To top

Spindle Boot Kit (SBR-KIT)

This replacement Spindle Boot Pack fits Ammco Models 3000, 4000, 4100, 7700. It includes a Neoprene spindle boot, screw feed dust boot, cross feed dust boot, C-Clip and Snap Ring for installation. All items are also available separately.Simple Seal with 3.55" OD.

To top

GT-4670 Drum Feed Nut for Ammco

Fit all Ammco models.

To top

GT-32111 Rotor Feed Screw for Ammco

For Ammco 4000.

To top

GT-9918 Drum Feed Screw for Ammco

For Ammco 4000.

To top

GT-10318 Rotor Feed Screw for Ammco

For Ammco Rotor Feed Screw (7000)

To top

29240 Boring Bar (1-1/2 in. hex x 16-1/2 in)

Fits Ammco 3850.

To top

5844 Boring Bar (1-1/2in Hex, 19-1/2in)

For Ammco 4100, 4000, 3000.

To top

5843 Boring Bar (1-1/2in Hex, 15-1/2in)

For Ammco 3000 and 4000.

To top

GT-10868X Rotor Feed Nut (early)

Fits early models 4000, 4100 & 7700.

Lead Screw Bushing.

To top

GT-10868X Rotor Feed Nut (late)

Fits late models 4000, 4100 & 7700. Replaces Ammco 28366

To top

C-Clip for Spindle Boot (SBR-4435)

Fits late models 4000, 4100 & 7700. Replaces Ammco 28366

To top

Sphere Washer Set of 2 (GT-3165)

Self centering washers for holding down bore bar or twin cutter.

To top

Nut Assembly for 6-1/2in. Stud (GT-11227)

For use with 6-1/2" Stud (sold separately).

For the long stud, 6 1/2in (GT-25913)

To top

Tooling Hold Down Stud Assembly (GT-25900)

Includes 6-1/2" Stud & Nut Assembly (both pieces also sold separately)

To top

Cross feed dust boot (3087):

· Essential for brake lathe operation

· Always keep extra boots on hand for

routine maintenance or emergency replacement

· Fit Ammco 3000, 4000, 4100, 7000 and 7700 brake lathes

 

 

 

Polyethylene Spindle Boot (3085)

Fits Ammco Models 3000, 4000, 4100, 7700

Screw Feed Dust Boot (3086)

Screw Feed Dust Boot for the Ammco 3000, 4000, 4100, 7000 and 7700 brake lathes. Keep extras on hand to routine maintenance or emergency replacement.

Cross Feed Shear Gear & C-Clip for 4000 & 4100 (7996)

 Fits Ammco 4000 & 4100

 

 

Replacement Locking Knob (6854)

Fits all Ammco models.

Replacement Seals for Ammco (3163: FEED SCREW, 3164: SPINDLE)

These Replacement Seals fits Ammco Brake Lathe Models 3000, 4000, 4100, 7000, 7700.

Choose from Feed Screw Seal with 1.250" OD